Single sided edge banding machine
with workpiece return LIGMATECH
Price: 31.500,00 €
DescriptionSingle sided edge banding machine
Type: KL 79/A20/S2-20MM
Coil or as strip, up to 20 mm edge thickness, in lenghtwise and crosswise feed.
- Feed stepless controllable 18 - 24 m/min
- Working height 950 mm
- Working width min.:
- 55 mm at workpiece thickness 22 mm, 100 mm at workpiece thickness 60 mm (depending on the workpiece length)
- Workpiece overhang 30 mm
- Workpiece thickness 12 - 60 mm
- Edge material strip max. 0,4 - 20 mm
- Edge cross sectional area strip max. 900 mm2
- Edge material coil 0,3 - 3 mm
- Edge cross sectional area max.: at PVC 135 mm2, at veneer 100 mm2
- Coil Ø max. 830 mm
- Floor condition should match the foundation plan.
- for rectangular feed at single sided processing.
-Workpiece dimensions max. 500 x 1600 mm
Anti-stick solvent application
-via spraying nozzles top/bottom
2 Motoren je 3 kW, 150 Hz, 9000 1/min.
to heat the workpiece edge before glue application for a better glue quality
Gluing unit A20:
Hot melt unit 0A34
for strip ware, massive edges and coil ware
Feed of strip ware via vacuum succer
Edge monitoring with automatical feed stop at missing edge
Pressure zone C
1 driven pre-pressure roller Ø 150 mm
6 post-pressure rollers Ø 70 mm
Pressure adjustments pneumatical
Central adjustment on different edge thicknesses
Automatical adjustment pressure zone Optimat
for automatical adjustment of pressure zone at different edge thickness
1 pc. chip removal conveyor for Optimat installed in machine stand.
End trimming unit HL 83 chamfer/straight
2 motors each 0,5 kW, 200 Hz., 12000 rpm.
for the end trimming of edge overhangs on frontal and rear edge
Edge thickness chamfer max. 3 mm
Automatical adjustment HL 81/83
for electropneumatical setup from chamfer to straight and stepless adjustment of foldable side stop for chamfer end trimming at different edge thicknesses.
Pneumatical adjustment end trimming motor lateral for electropneumatical side adjustments of end trimming motors on 2 positions.
Position 1 - Flush trimming
Position 2 - End trimming with overhang - for post-milling with profile milling unit
1 pc rough milling unit 1,5 KW OPTIMAT
2 motors one above the other each 1,5 kW, 200 HZ., 12000 rpm.
1 pc pneumatical adjustment rough milling unit OPTIMAT on 2 positions
Position 1 - Rough milling with edge overhang (approx. 0,2 mm)
Position 2 - Flush milling without edge overhang
1 pc. profile milling unit FK 13 8-fold automatical
for processing of edge overhangs on the workpiece top- and bottom edge as well for milling arround top- and bottom edge in connection to end trimming unit and rough milling unit.
2 Motors each 0,4 kW, 200 Hz., 12000 rpm.
Automatical 8 -fold tool changer.
Selector switch lengthwise-/surround milling.
Feed max. 20 m/min.
Workpiece length min. - 240 mm single sidede, 120 mm double sided
Distance between workpieces min. 650 mm
Workpiece thickness 12 - 60 mm
Edge thickness max. 5 mm
Automatical adjustment for FK-device
for automatical adjustment at same radii on different edge thickness f.e. R=3 mm on egde thickness 3 mm or 6 mm and for moving out of the working area.
1 x Universal milling unit 4 KW controlled UF11
- installed on back side of miller stand
- Cross support with spindle adjustment
- 1 Motor 4 kW, 150 Hz., 9000 rpm
- Swivable max. 90 degrees
1 pc. re-cleaning unit profile
tracing from above, bottom and side for chamfering or rounding of rough milled PVC-edges. Blowing nozzles electropneumatical controlled.
1 pc. PVC-chip tear off top/bottom for better PVC-chip removal
2 pcs. pneumatic adjustment re-cleaning PROFIL OPTIMAT
for electropneumatical lateral move out of the working area.
1 pc. re-cleaning device glued joint
Remove of glue rests in the area of glued joint. Tracing from top and bottom.
1 pc. pneumatic adjusments re-cleaning PROFIL OPTIMAT
for electropneumatical lateral move out of the working area
1 pc. buffing unit top and bottom with oscilating for making the edges handy.
2 Motors each 0,25 kW, tilt and height adjustable
LIGMATECH workpiece return
ZHR 10/S left hand side 9500 MM
For edge banding machine left hand side, length approx. 9500 mm
The workpiece return ZHR 10 allows the one-man-operation of single sided throughfeed machines. Workpieces which come out of the machine are transported to a roller conveyor and will be crosswise transfered via a driven v-belt and will be returned via a belt and a roller table.
The option turning plus top pressure allows the 90° turn of workpieces coming out of the machine and will be lengthwise returned
The following version consists of:
- Roller conveyor TR 10/42/22 with takeover v-belts of the KL
Turning plate with turn support, thickness adjustment manual
Small parts construction set in front of cycle fence
Crosswise v-belt, pneum. liftable
Switch cabinet with control and chain
- Roller conveyor TR 10/30/10, with crosswise v-belt,
pneum. liftable, stroke 80 mm
2 pcs. belt conveyor MTB 05/50/09
Length 5000 mm
Width 900 mm
Min.: Length 300 mm
Width: 120 mm
Max: Length 3000 mm
Width 1000 mm
Weight: 50 kg
at turn crosswise to lengthwise:
Length: 2000 mm
Width: 600 mm
Stepless controllable of 15 - 60 m/min.
The specifications and descriptions are a copy of the order confirmation at that time. Datas are for information and are not binding.